ScanSettings

AUTO_BATCH_MIN_REPORT_DELAY_MILLIS

static val AUTO_BATCH_MIN_REPORT_DELAY_MILLIS: Long

Minimum report delay for ScanSettings.CALLBACK_TYPE_ALL_MATCHES_AUTO_BATCH.

Value: 600000L

CALLBACK_TYPE_ALL_MATCHES

static val CALLBACK_TYPE_ALL_MATCHES: Int

Trigger a callback for every Bluetooth advertisement found that matches the filter criteria. If no filter is active, all advertisement packets are reported.

Value: 1

CALLBACK_TYPE_ALL_MATCHES_AUTO_BATCH

static val CALLBACK_TYPE_ALL_MATCHES_AUTO_BATCH: Int

A result callback for every Bluetooth advertisement found that matches the filter criteria is only triggered when screen is turned on. While the screen is turned off, the advertisements are batched and the batched result callbacks are triggered every report delay. When the batch scan with this callback type is activated, the batched result callbacks are also triggered while turning on screen or disabling the scan. This callback type must be used with a report delay of ScanSettings.AUTO_BATCH_MIN_REPORT_DELAY_MILLIS or greater.

Value: 8

CALLBACK_TYPE_FIRST_MATCH

static val CALLBACK_TYPE_FIRST_MATCH: Int

A result callback is only triggered for the first advertisement packet received that matches the filter criteria.

Value: 2

CALLBACK_TYPE_MATCH_LOST

static val CALLBACK_TYPE_MATCH_LOST: Int

Receive a callback when advertisements are no longer received from a device that has been previously reported by a first match callback.

Value: 4

MATCH_MODE_AGGRESSIVE

static val MATCH_MODE_AGGRESSIVE: Int

In Aggressive mode, hw will determine a match sooner even with feeble signal strength and few number of sightings/match in a duration.

Value: 1

MATCH_MODE_STICKY

static val MATCH_MODE_STICKY: Int

For sticky mode, higher threshold of signal strength and sightings is required before reporting by hw.

Value: 2

MATCH_NUM_FEW_ADVERTISEMENT

static val MATCH_NUM_FEW_ADVERTISEMENT: Int

Match few advertisement per filter, depends on current capability and availability of the resources in hw.

Value: 2

MATCH_NUM_MAX_ADVERTISEMENT

static val MATCH_NUM_MAX_ADVERTISEMENT: Int

Match as many advertisement per filter as hw could allow, depends on current capability and availability of the resources in hw.

Value: 3

MATCH_NUM_ONE_ADVERTISEMENT

static val MATCH_NUM_ONE_ADVERTISEMENT: Int

Determines how many advertisements to match per filter, as this is scarce hw resource. Match one advertisement per filter.

Value: 1

PHY_LE_ALL_SUPPORTED

static val PHY_LE_ALL_SUPPORTED: Int

Use all supported PHYs for scanning. This will check the controller capabilities, and start the scan on 1Mbit and LE Coded PHYs if supported, or on the 1Mbit PHY only.

Value: 255

SCAN_MODE_BALANCED

static val SCAN_MODE_BALANCED: Int

Perform Bluetooth LE scan in balanced power mode. Scan results are returned at a rate that provides a good trade-off between scan frequency and power consumption.

Value: 1

SCAN_MODE_LOW_LATENCY

static val SCAN_MODE_LOW_LATENCY: Int

Scan using highest duty cycle. It's recommended to only use this mode when the application is running in the foreground.

Value: 2

SCAN_MODE_LOW_POWER

static val SCAN_MODE_LOW_POWER: Int

Perform Bluetooth LE scan in low power mode. This is the default scan mode as it consumes the least power. This mode is enforced if the scanning application is not in foreground.

Value: 0

SCAN_MODE_OPPORTUNISTIC

static val SCAN_MODE_OPPORTUNISTIC: Int

A special Bluetooth LE scan mode. Applications using this scan mode will passively listen for other scan results without starting BLE scans themselves.

Value: -1

describeContents

fun describeContents(): Int

getCallbackType

fun getCallbackType(): Int

getLegacy

fun getLegacy(): Boolean

Returns whether only legacy advertisements will be returned. Legacy advertisements include advertisements as specified by the Bluetooth core specification 4.2 and below.

getPhy

fun getPhy(): Int

Returns the physical layer used during a scan.

getReportDelayMillis

fun getReportDelayMillis(): Long

Returns report delay timestamp based on the device clock.

getScanMode

fun getScanMode(): Int

getScanResultType

fun getScanResultType(): Int

writeToParcel

fun writeToParcel(
    dest: Parcel, 
    flags: Int
): Unit

CREATOR

static val CREATOR: Parcelable.Creator<ScanSettings!>